Tenax

Booster Tile Cleaner & Porcelain Stain Remover – 1 Liter

TILE CLEANER & PORCELAIN STAIN REMOVERBooster is a multipurpose tile and hard surface cleansing product that can be used for a variety of cleaning tasks. It can be used as a stain remover (full strength) on specific materials or as a cleaner (diluted). Booster Tile Cleaner can be mixed for use in removing the following discolorations on hard surfaces:Stubborn Organic DirtRubber MarksWaxesEpoxy ResidueGENERAL PURPOSE CLEANINGBooster can be used as a high powered cleaner on a variety of materials. When it is diluted to the proper strength, it can be used to clean stubborn dirt and grime from the following surfaces:CeramicPorcelainUnpolished StoneGlazed CeramicCementPVCGraniteUnpolished MarbleNon-glossy Cement AgglomerationTo use Booster as a power cleansing agent, simply follow these instructions:Mix 1 part Booster with 20 parts water.Apply the mixture to the surface to be cleaned.Leave mixture on surface for 5-10 minutes.Work the mixture using a brush while wearing hand protection.Rinse the surface thoroughly to remove all Booster.CAUTION:When using Booster as a Tile Cleaner, be sure to wear appropriate hand protection. Additionally, for stubborn stains higher strength mixtures can be used. If you need to use a stronger mix, be sure to test it in an inconspicuous location before using. Tile cleaner to water ratios include:BOOSTER:WATER MIX RATIOS1:20 = Standard Ratio (Recommended)1:10 = Tougher Dirts Ratio1:5 = Stubborn Dirts RatioPORCELAIN STAIN REMOVALBooster tile cleaner and porcelain stain remover can be used to remove stains from porcelain stoneware. To use Booster as a porcelain stoneware stain remover apply as follows:Apply undiluted Booster to the porcelain sotneware using a small brush or a paint brush.Allow the Booster to sit on the area for approximately 10 minutes.Use a scrub brush in order to scrub away residues.Rinse thoroughly with water.For particularly stubborn stains, cover the stain with plastic and leave covered for several hours on epoxy residues.SAFETY RULES:Read the information on the safety data sheet and the instructions on the package/can before use.WARNINGS:Keep out of the reach of children.Avoid contact with the eyes and skin.Do not mix with other substances.Do not use as a cleaner for waxed and glossy surfaces.SHELF LIFE:The product will last at least 12 months in normal condition, kept away from heat, humidity and sunlight. Close the package after usage.

Booster Tile Cleaner & Porcelain Stain Remover – 1 Liter Read More »

Tenax JET Self Polishing Varnish Spray – 500ml

Size: 500 mlJet is a liquid aerosol. Apply to a non polished surface that was missed during fabrication or too hard to reach or polish. The varnish forms a film or coating on the surface that creates a polished look. Completely dry in 15 minutes. Cannot be walked on. Great for job site touch ups.Directions: Make sure surface to be treated is clean and completely dry. Spread a thin and uniform layer on the surface. Wait a few minutes until the surface is dry. We suggest you test this product on a small hidden area before use.This product treats approximately 161-215 sq. ft. depending on the porosity of the surface.Shelf Life: This product will last at least 6 months if kept between 65° and 77°. Keep away from heat, humidity and sunlight.

Tenax JET Self Polishing Varnish Spray – 500ml Read More »

Tenax BrioAction2 Mold Remover – 1 Liter

Brio Action Mold Remover is a sanitizing, biodegradable (more than 90% biodegradable) cleaner for marble, granite, terra-cotta, ceramic, terra-cotta, brick, block, concrete, stone or concrete based furniture, benches, decorative borders, and other hard surfaces. Brio Action Mold is specifically designed to remove mold, moss, algae, musk, and all other fungus products from all surfaces. Brio Action Mold Remover is also an effective sanitizer, and it is non toxic and environmentally friendly. Clean up is a cinch! Because it is biodegradable, it can simply be washed down the drain! Directions:1. Sweep up any loose dirt and clean surface to be treated.2. Spread product generously on surface to be treated using a brush or similar equipment. The layer of product must be at least 1mm thick.3. Leave the product on the surface depending on the degree of the stain. We recommend an average time of 30-60 minutes at 68°. In case of lighter soiling or higher temperature reduce the time to prevent product from drying. During this time the product also sanitizes the surface.4. Rinse thoroughly with water. Depending on the roughness of the surface (smooth, brushed, etc.), the type of dirt (residues of cement, mold, etc.) it may be useful to scour with a brush while rinsing so as to remove any dissolved material from rougher surfaces.5. Discard the solution as it has already exhausted its effectiveness and cannot be reused.6. In case of stubborn dirt and insufficient cleansing, repeat the treatment following steps 1 thru 47. It is recommended to test this product on a small hidden area to determine the correct contact time. On some very shiny surfaces this cleanser may cause partial loss of shine.8. In order to protect the surface and improve its appearance we suggest you treat the surface with a Tenax protective sealer or wax which should be applied to a completely dry surface. Shelf Life:This product will last at least 12 months if kept between 65° and 77°. Keep away from heat, humidity and sunlight.

Tenax BrioAction2 Mold Remover – 1 Liter Read More »

Tenax Wax Remover – 1 Liter

Size: 1 LiterTenax Wax Remover removes liquid and paste waxes off the surfaces of stone. Transparent in colorDirections:Simply pour the the Wax Remover onto the surface, let stand for 5-10 minutes. Agitate the surface using a brush. Remove with rags or towels.Shelf Life:This product will last at least 2 years if kept between 65° and 77°. Keep away from heat, humidity and sunlight.

Tenax Wax Remover – 1 Liter Read More »